| ¡¡Model£º |
|
SVPG
|
-
|
3
|
18
|
-
|
10MPa
|
|
1
|
|
2
|
3
|
|
4
|
|
1
|
Models
|
Switching valve with pressure gauge glycerin
|
|
2
|
Hole
|
£³£º£³Hole
|
|
£¶£º£¶Hole
|
|
3
|
Connection Dental mouth diameter
|
18£ºRc1/8
|
|
14£ºRc1/4
|
|
4
|
The maximum scale pressure gauge
|
4 £º 0¡«4MPa
6 £º 0¡«6MPa
10 £º 0¡«10MPa
16 £º 0¡«16MPa
25 £º 0¡«25MPa
40 £º 0¡«40MPa
|
|
¡¡Specialty£º
|
| £ª |
No longer need to switch the valve with pressure gauge and tube, so a substantial reduction of the allocation of working hours. And do not need to process pressure gauge panel mounting Hole¡£ |
| £ª |
Simply align the arrow handle loop number can be easily measured circuit pressure¡£ |
| £ª |
Recorded between the Hole "0" position, will handle the arrow aimed "0" position, you will gauge the residual pressure within the discharge outfall, in addition to measuring the pressure, the pressure gauge when the instruction pointer constant " 0 "position, from the pressure gauge and then greatly improve the precision and durability. |
|
|
¡¡Specification£º
|
|
Maximum pressure
|
21MPa
|
|
Pressure-resistant
|
38MPa
|
|
Installation
|
Panel Mount
|
|
For fluid
|
General petroleum actuation oil (lipid phosphate as mobile oil, water - glycol oil, please be contact actuation£©
|
|
Leakage from the discharge port
|
-20Degree ~ -60 degree
|
|
Back pressure from the discharge port to allow
|
£¼Set the conditions£¾
To move oil £º ISO VG32 Oil temperature £º 45±5¡æ
|
7MPa £º20cm3£¯minThe following
14MPa £º30cm3£¯minThe following
21MPa £º40cm3£¯minThe following |
|
Net weight
|
2500g
|
|
| ¡¡Caution£º |
| £ª |
Hole in the switching valve for the piping, it is necessary to balance the Hole in the pressure to connect with¡£ |
| £ª |
The valve seal structure of the main valve outside diameter and inside diameter of about 10μ metal with gap sealing. If dirt, etc. attached to the handle will send Shibuya, turn no case, so please pay attention to the situation for moving dirty oil¡£ |
| £ª |
Washing piping, please be careful not to dirty the washing oil into the valve¡£ |
| £ª |
Please change the handle on a regular basis to implement the operation. Not to handle long-term conversion, they would produce hydraulic adhesion phenomenon and become fat, Shibuya handle operation¡£ |
| £ª |
Discharge to maintain the internal pressure, the valve stem may be off. Be sure to install the vent pipe discharge¡£ |
|
| ¡¡Use Cases£º |
| £ª |
Plastic injection molding machine, rubber injection molding machine |
| £ª |
Hydraulic Press (powders, ceramics, rubber stamping£© |
| £ª |
Machine tools (large-scale machine tools, special purpose machine, NC Sawing Machine£© |
| £ª |
Hydraulic unit (industrial, machine tools, ships, valve stations£© |
|
| ¡¡List of hose connector £º |
| £ª |
Plastic injection molding machine, rubber injection molding machine |
.jpg) |
| £ª |
Hydraulic Press (powders, ceramics, rubber stamping£© |
| £ª |
Machine tools (large-scale machine tools, special purpose machine, NC Sawing Machine£© |
| £ª |
Hydraulic unit (industrial, machine tools, ships, valve stations£© |
|
|
|
|
|
|
|
|
¡¡
¡¡US-series